SIKORA PREHEATER 6000 TC
Conductor preheater with non-contact conductor temperature measurement and control
SIKORA PREHEATER 6000 TC is a conductor preheater installed upstream of the extruder, which heats the conductor conductively to 50–150 °C (optionally up to 250 °C). The conductor temperature is measured without contact at the exit and is used directly to control the heating power.
Benefits
- Continuous non-contact measurement and control of conductor temperature using an infrared camera
- Repeatable processes and elimination of operator errors
- Optimum adhesion of the insulation material to the conductor
- Reliable capacitance values in LAN cable production
- Wire break detection
- Uniform conductor temperature thanks to a heating frequency of 2,000 Hz
- Nominal temperature entered on the unit display or from the line control system
- Large LED displays showing the measured temperature on both sides of the unit
- Optional adaptive heating for higher line speeds
- Preheating of conductors upstream of the extruder in cable and wire production
- LAN cable production
- Copper, aluminium and steel conductors with a diameter of 0.32–2.8 mm (0.08–6 mm²)
We supply the equipment configured for your application. In your inquiry, please state the material processed, the required throughput and the line parameters – we will prepare a tailored quotation.
Need help choosing? Call us on +420 571 647 228 or write to info@azurr-tech.cz.
Technical data
| Operating principle | Conductive heating via a short-circuit pulley; optionally with non-contact conductor temperature measurement and control |
|---|---|
| Conductor material | Copper, aluminium, steel |
| Diameter range | 0.32–2.8 mm (0.08–6 mm²) depending on version; standard system 0.45–2.8 mm (0.16–6 mm²); larger diameters on request |
| Line speed | 50–2,500 m/min |
| Heating frequency | 2 000 Hz |
| Power | 10, 20, 30, 35 kW |
| Conductor temperature | 50–150 °C (optionally 250 °C) at an initial conductor temperature of 20 °C; temperatures below 50 °C on request |
| Interface | Ethernet/UDP, serial RS485 + RS232; optionally Profibus-DP, analogue input and output 0–10 V, module for Profinet IO, EtherNet/IP, Profibus-DP, DeviceNet, CANopen |
| Power supply | 3-phase 400 V ±10 %, 47–63 Hz |
| Permissible ambient temperature | 15–45 °C |
| Humidity | max. 95 %, non-condensing |
Description
SIKORA PREHEATER 6000 TC (Temperature Controlled) is a conductor preheater that is placed upstream of the extruder and heats the wire by conductive heating to 50 to 150 °C (optionally up to 250 °C). A heating frequency of 2,000 Hz at a maximum power of 35 kW ensures a uniform conductor temperature.
A characteristic feature is the non-contact measurement of the conductor temperature inside the unit, with direct feedback to the power control. Without accurate measurement and control of the conductor temperature, the achievable accuracy is affected by a number of factors – ambient temperature, initial conductor temperature and in particular the temperature development of the conductor guide short-circuit pulley during the first 10 to 20 minutes after starting or interrupting production.
The conductor temperature is measured continuously at the preheater exit by a non-contact infrared camera and the power is controlled continuously, so that the actual temperature matches the required temperature for all conductor cross-sections and at all line speeds. The required conductor temperature is entered directly on the unit display or from the line control system; this eliminates operator errors and ensures repeatable processes. The measured temperature is shown on large LED displays on both sides of the unit.
The units are supplied in power ratings of 10, 20, 30 and 35 kW and cover conductor diameters of 0.32–2.8 mm (cross-section 0.08–6 mm²); units for larger sizes are available on request. The maximum line speed reaches up to 2,500 m/min depending on the required temperature, the model and the optional adaptive heating, which supplies a higher current and allows a higher line speed at a given nominal temperature. To select a suitable type, SIKORA offers the online PREHEATER 6000 TC Power Calculator tool.
Optional equipment
More products in this category
SIKORA ULTRATEMP 6000
Ultrasonic measurement of PE melt temperature between the extruder and the crossheadAll versions in the Temperature, length and preheating category (3 items)